Fibre Glass-Evercoat Co., Inc. MSDS Number: 100887

6600 Cornell Road Date: 11/13/00

Cincinnati, OH 45242 Page 1 of 2

Phone: (513) 489-7600

Emergency Phone: CHEMTREC (800) 424-9300

Product Name: METAL-2-METAL Aluminum-Filled Body Repair Product Number(s):887, 889 and 899

* - Indicates chemical substance is subject to reporting requirements under SARA Title III, Part 313.

**- PEL is for Total Dust ; Respirable fraction is 5 mg/m3

mppcf- millions of particles per cubic foot of air

N/E - Not Established. N/A - Not Applicable.

Hazardous Decomposition Products: Fumes may be produced when material is heated to decomposition. Fumes may contain carbon

monoxide, carbon dioxide, and various hydrocarbons.

Special Fire fighting Procedures: Use full protective equipment including NIOSH-approved self-contained breathing apparatus. Water

may be used to cool containers to prevent pressure build-up which may rupture containers.

Unusual Fire and Explosion Hazards: Vapors are heavier than air and may travel along the floor and be ignited by sparks or flames at a distance from where the material is being used.

If Material Is Spilled: Remove all sources of ignition. Ventilate the area. Wear protective equipment (See Section H). Avoid breathing

vapors. Contain spill. Collect with inert absorbent and remove. Dispose of properly.

Waste Disposal Procedures: Dispose of in accordance with federal, state, and local regulations. Waste from this product may be

hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. Waste must be tested for

ignitability to determine the applicable EPA hazardous waste numbers. Before attempting clean-up or disposing of material,

refer to hazard information in other sections of this sheet.

Fibre Glass-Evercoat Co., Inc. - 6600 Cornell Road - Cincinnati, OH 45242 Page 2 of 2 MSDS Number: 100887

Chronic Effects Of Overexposure:

Excessive overexposure to styrene has been found to cause the following effects in laboratory animals: Liver

abnormalities, kidney damage and lung damage. (See also Section J).

Acute Effects Of Overexposure:

EYES: Contact with liquid or vapor may result in irritation, redness, tearing, and blurred vision.

SKIN: Contact with wet material may result in irritation of the skin and possible dermatitis.

INHALATION: Excessive inhalation of vapors may cause nasal and respiratory irritation, acute nervous

system depression, fatigue, weakness, nausea, headache, and dizziness.

SWALLOWING: Ingestion of this material may cause gastrointestinal irritation, nausea, diarrhea, and vomiting. Aspiration

of material into the lungs due to vomiting may produce chemical pneumonitis which can be fatal.

First Aid Procedures:

IF IN EYES: Flush immediately with large amounts of water for at least fifteen minutes. See physician for medical

treatment.

IF ON SKIN: Immediately wash affected area with soap and water. Remove contaminated clothing. Consult a physician if

irritation develops.

IF INHALED: Remove person to fresh air. Restore breathing. Keep person warm and quiet. Treat symptomatically. Get

medical attention.

IF SWALLOWED: Keep person warm and quiet. Consult a physician or poison control center immediately.

Eye Protection: Splash goggles should be worn.

Skin Protection: Protective gloves and proper clothing should be worn to prevent skin contact. Gloves should be made of neoprene or

natural rubber. Barrier cream may be worn for additional skin protection.

Respiratory Protection: Use NIOSH-approved respirators designed to remove particulate matter and organic solvent vapors.

Ventilation: General dilution or local exhaust ventilation should be provided to keep exposures below acceptable limits (Section B)

and to keep solvent vapors below the lower explosion limit.

Other Protective Equipment: Impermeable clothing should be worn to prevent prolonged or repeated contact of wet material with the

skin.

Hygienic Practices: Always wash hands after using this material, and before eating, drinking, or smoking.

Precautions To Be Taken In Handling And Storage: Store material in a cool, well-ventilated area. Do not store at temperatures above

75 ° F. Do not use or store near heat, sparks, or open flame. Keep containers tightly closed. Avoid contact with incompatible

materials.

Other Precautions: This product must be mixed with catalyst prior to use. Please refer to Material Safety Data Sheet for catalyst before

using. If product is to be sanded, the PEL/TLV of 10 mg/m3 for nuisance dusts should be observed. Keep out of reach of

children. Do not take internally. Avoid contact with eyes and skin.

The International Agency for Research on Cancer (IARC) has classified styrene as a group 2B Carcinogen (possibly carcinogenic to

humans). This classification is not based on evidence that styrene may be carcinogenic, but rather on a revised definition for Group 2B,

and consideration of new data on styrene oxide. A number of lifetime animal studies with styrene, including those in the NCI Bioassay

Program, have not shown styrene to be carcinogenic.

WARNING: This product contains a chemical known to the state of California to cause cancer.

THE INFORMATION ACCUMULATED HEREIN HAS BEEN COMPILED FROM CURRENT SOURCES WHICH ARE BELIEVED TO BE ACCURATE AND

RELIABLE. SINCE IT IS NOT POSSIBLE TO ANTICIPATE ALL CIRCUMSTANCES OF USE, RECIPIENTS ARE ADVISED TO CONFIRM, IN ADVANCE OF

NEED, THAT THE INFORMATION IS CURRENT, APPLICABLE AND SUITABLE TO THEIR CIRCUMSTANCES.